Empty ECO Spool
Empty ECO Spool
Empty 3D Printer Filament Spool
The first reusable spooling system to be sold in Australia. ECO spools are made from high-impact polycarbonate and designed to be reloaded with all filament refills. They're sturdy and durable enough to last a lifetime. The ECO spool accepts all our filament refills across our entire range and cuts down on the amount of single use plastic generated from the 3D printing process.
Held together with 4 x 3mm hex screws, the spool is designed to be taken apart and refilled time and time again.
|
Construction |
Polycarbonate, Steel |
Colour: |
Transparent |
Weight: |
225g ± 2g |
Required Tools: |
3mm Hex Key |
TECH SPECS
+ What is a Standard Print Co. ECO Spool?
The first reusable spooling system to be sold in Australia. ECO spools are made from high-impact polycarbonate and designed to be reloaded with all filament refills. They're sturdy and durable enough to last a lifetime. The ECO spool accepts all our filament refills across our entire range and cuts down on the amount of single use plastic generated from the 3D printing process.
Held together with 4 x 3mm hex screws, the spool is designed to be taken apart and refilled time and time again.
+ How do I refill a Standard Print Co. ECO Spool.
| Step 1: | To re-spool an empty Standard Print Co. ECO spool, first loosen the four securing screws on the reverse face of the spool with a 3mm hex key. |
| Step 2: | After removing the backing plate, slide your naked refill onto the spool |
| Do not cut the filament coil's securing straps at this stage. Doing so will result in the filament uncoiling completely, making it next to impossible to recoil in an orderly manner. | |
| Step 3: | Secure the end of the filament located on the inner diameter of the refill filament coil in the groove located on the inner diameter of the ECO spool before replacing the backing plate of the inner spool. Failure to do this will cause the refill filament coil to spin independently of the ECO spool. |
| Step 4: | Resecure the four screws holding backing plate to the ECO spool. |
| Step 5: | Only after the filament has been secured and backing plate replaced, should a pair of scissors be used to carefully cut and remove the four plastic straps holding the filament coil together being careful not to cut or damage the filament itself. |
+ Do all refill filaments fit on an ECO Spool?
Yes. All refills across our entire material range are designed to fit on our ECO spool.
Ready to get printing?
Refill and reload. The ultimate refill bundle containing our most popular shades.
Refill and reload. A refill bundle containing some of our most popular colours.
Refill and reload. The ultimate refill bundle containing our most popular colours.
3D Printer Filament
ABS 1.75mm Black 1KG ECO/Refill
Weight: 1kg
Colour: Black
Material: ABS
Nozzle Temperature: 240°C - 250°C*
Bed Temperature: 80°C - 110°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
ABS 1.75mm Grey 1KG ECO
Weight: 1kg
Colour: Grey
Material: ABS
Nozzle Temperature: 240°C - 250°C*
Bed Temperature: 80°C - 110°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
ABS 1.75mm Natural 1KG ECO
Weight: 1kg
Colour: Natural (Transparent)
Material: ABS
Nozzle Temperature: 240°C - 250°C*
Bed Temperature: 80°C - 110°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
ABS 1.75mm Natural 1KG ECO
Weight: 1kg
Colour: Natural
Material: ABS
Nozzle Temperature: 240°C - 250°C*
Bed Temperature: 80°C - 110°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
ABS 1.75mm Orange 1KG ECO
Weight: 1kg
Colour: Orange
Material: ABS
Nozzle Temperature: 240°C - 250°C*
Bed Temperature: 80°C - 110°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
ABS 1.75mm Lime Green 1KG ECO
Weight: 1kg
Colour: Lime Green
Material: ABS
Nozzle Temperature: 240°C - 250°C*
Bed Temperature: 80°C - 110°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
ABS 1.75mm Red 1KG ECO
Weight: 1kg
Colour: Red
Material: ABS
Nozzle Temperature: 240°C - 250°C*
Bed Temperature: 80°C - 110°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
ABS 1.75mm British Racing Green 1KG ECO
Weight: 1kg
Colour: British Racing Green
Material: ABS
Nozzle Temperature: 240°C - 250°C*
Bed Temperature: 80°C - 110°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
ASA 1.75mm Black 1KG ECO/Refill
Weight: 1kg
Colour: Black
Material: ASA
Nozzle Temperature: 230°C - 260°C*
Bed Temperature: 100°C - 120°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
PETG Carbon Fibre 1.75mm Black 1KG ECO
Weight: 1kg
Colour: Matte Black
Material: PETG Carbon Fibre
Nozzle Temperature: 230°C - 250°C*
Bed Temperature: 80°C - 100°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
PETG 1.75mm Black 1KG ECO/Refill
Weight: 1kg
Colour: Black
Material: PETG
Nozzle Temperature: 240°C - 260°C*
Bed Temperature: 0°C - 75°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
PETG 1.75mm White 1KG ECO
Weight: 1kg
Colour: White
Material: PETG
Nozzle Temperature: 220°C - 240°C*
Bed Temperature: 0°C - 50°C
Diameter: 1.75mm ± 0.03mm
3D Printer Filament
PETG 1.75mm Natural 1KG ECO
Weight: 1kg
Colour: Natural
Material: PETG
Nozzle Temperature: 210°C - 240°C*
Bed Temperature: 0°C - 75°C
Diameter: 1.75mm ± 0.03mm
Buy a kit once, refill & save forever.